+91 9008001602        080 - 40969981     technofist.projects@gmail.com

Automobile Based Projects

IT-CDP is one of the best Academic project center training institution in bangalore,india for final year mechanical engineering students. we provide training on Atumobile Engineering projects which includes Design,Development and implementation of an automotive products for engineering students.we provide automobile projects using latest technolgies like steering mechanism, safety feature, automatic jack, rain detection, automatic tyre inflator, hybrid Vehicle, electrical vehicle, Engine effeciency, Automatic braking etc.., students belonging to final year they can use these projects as mega projects.

TAG001
AIR BRAKE SYSTEM USING EXHAUST GAS

ABSTRACT--The aim is to design and to develop an air brake system based on exhaust gas is called “fabrication of air brake system using engine exhaust gas”. The main aim of this project is to reduce the workloads of the engine drive to operate the air compressor, because here the compressor is not operated by the engine drive. Here we are placing a turbine in the path of exhaust from the engine. The turbine is connected to a dynamo by means of coupling, which is used to generate power. Depending upon the airflow the turbine will start rotating, and then the dynamo will also starts to rotate. A dynamo is a device which is used to convert the kinetic energy into electrical energy. The generated power can be stored in the battery and then this electric power has loaded to the D.C compressor. The air compressor compresses the atmospheric air and it stored in the air tank and the air tank has pressure relief valve to control the pressure in the tank. The air tank supplies the compressed pneumatic power to the pneumatic actuator through solenoid valve to apply brake. The pneumatic actuator is a double acting cylinder which converts hydraulic energy into linear motion. Keyword: - Dynamo, DC Compressor, and Pressure relief valve etc….Contact:
 +91-9008001602
 080-40969981

TAG002
AUTOMATIC TIRE INFLATION AND DEFLATION SYSTEM

ABSTRACT--The main aim of our project is to develop a “Automatic tyre inflation and deflation system” .This can be placed in all automobiles while long drives and that can be utilized while climbing uphill or down hills. It is very necessary for the every automobile to be cautious while driving through long distances. So we have fabricated this machine to fill the air automatically by using control units. In this project main function is suddenly the air is decreased to the automobile vehicles the sensor signal alerted to the person when the use of air tank to fill the air in the tyre. Then the air pressure is increased to the tyre in the vehicle i t is same as the process of indicating the sensor signal through the person when the use of solenoid valve to reduce the excess air in the tyre Contact:
 +91-9008001602
 080-40969981

TAG003
BUTTON OPREATED GEAR SHIFTING

ABSTRACT--The main objective of this concept is used to apply the gear by using automation system in automobiles. This is the new innovative model mainly used for the vehicles to control the vehicle. In this project we design the automatic gear changing mechanism in two wheeler vehicles by using the electromagnet devices. This is very useful for the gear changing mechanism in automobile vehicles. By using this we can easily control the vehicle and improve the performance of the vehicle also we can avoid the wear and tear of the gear. Contact:
 +91-9008001602
 080-40969981

TAG004
DEVELOPMENT OF HYBRID BIKE

ABSTRACT--The concern over the environment with respect to pollution, conservation of fuel resources in the world, the automotive industry has entered into a new dimension in production of more fuel efficient, low emission vehicles and new technologies. One of the greatest innovations is Hybrid Electric Vehicle (HEV). The hybrid electric vehicle consists of two or more energy sources for total propulsion of the vehicle. In this paper, two independent propulsions, ICE and electric motor are independently operated for combined effort derivation in total propulsion of the vehicle. The Combined effort of ICE and Electric motor in propelling the vehicle more suitable for country like India is being analyzed in this paper. The ICE will be active in initial pickup and electric motor acts as supportive propulsion deriver. The test area chosen is Mysore City, India in deriving the driving cycle. Contact:
 +91-9008001602
 080-40969981

TAG005
INTELLIGENT REVERSE BRAKING SYSTEM

ABSTRACT--The aim is to design and develop a control system based on intelligent electronically controlled automotive braking system is called “INTELLIGENT REVERSE BRAKING SYSTEM”. Sensor Operated Pneumatic Brake consists of IR transmitter and Receiver circuit, Control Unit, Pneumatic breaking system. The IR sensor is used to detect the obstacle. There is any obstacle in the path, the IR sensor senses the obstacle and giving the control signal to the breaking system. The pneumatic breaking system is used to brake the system. So basically here the car brakes on its own by determining the distance from the object. The IR TRANSMITTER circuit is to transmit the Infra-Red rays. If any obstacle is there in a path, the Infra-Red rays reflected. This reflected Infra-Red rays are received by the receiver circuit is called “IR RECEIVER”. The IR receiver circuit receives the reflected IR rays and giving the control signal to the control circuit. The control circuit is used to activate the solenoid valve. Contact:
 +91-9008001602
 080-40969981

TAG006
DEVELOPMENT OF AUTOMATIC POWER WINDOW MECHANISM

ABSTRACT--We have seen how severe is bus disasters on fire, accident etc, to avoid causalities and human lives here we are proposing power window mechanism. On sensing any danger in the form of fire and smoke the window automatically will slide down making way for passenger way out from the vehicle. This cool device is the heart of a power-window system. The win­dow lift on most cars uses a really neat linkage to lift the window glass while keeping it level. A small electric motor is attached to a worm gear and several other spur gears to create a large gear reduction, giving it enough torque to lift the window. Contact:
 +91-9008001602
 080-40969981

TAG007
DEVELOPMENT OF REGENERATIVE BRAKING SYSTEM – ELECTRIC

ABSTRACT--As the basic law of Physics says ‘energy can neither be created nor be destroyed it can only be converted from one form to another’. During huge amount of energy is lost to atmosphere as heat. It will be good if we could store this energy somehow which is otherwise getting wasted out and reuse it next time we started to accelerate. Regenerative braking refers to a system in which the kinetic energy of the vehicle is stored temporarily, as an accumulative energy, during deceleration, and is reused as kinetic energy during acceleration or running. Regenerative braking is a small, yet very important, step toward our eventual independence from fossil fuels. These kinds of brakes allow batteries to be used for longer periods of time without the need to be plugged into an external charger. These types of brakes also extend the driving range of fully electric vehicles. Regenerative braking is a way to extend range of the electric vehicles. In many hybrid vehicles cases, this system is also applied hybrid vehicles to improve fuel economy. A normal car is only about 20% efficient, meaning some 80% of the energy it expends is wasted as heat created by friction. Contact:
 +91-9008001602
 080-40969981

TAG008
RFID BASED SPEED CONTROLLER

ABSTRACT--This project aims at automatically controlling the speed of vehicles at speed restricted areas such as schools, hospital zones, traffic signals etc. Nowadays the drivers drive vehicles at high speed even in speed limited areas without considering the safety of the public. The traffic police are not able to control them with full effect. Also it is not practical to monitor these areas throughout. This paper paves way for controlling the speed of the vehicles within certain limit in restricted zones without interruption of the drivers. An RFID is used for this purpose. The RFID reader is attached along with the vehicle and the RFID Tag with these Zones. These tags are programmed to send a coded signal when the reader comes in proximity. Whenever the vehicles enter into these zones their receivers will receive this code and the speed of the vehicles is controlled automatically with the help of the micro controller unit present inside the vehicle. The tags are placed at the beginning and the end of the regions for which the speed should be reduced. Contact:
 +91-9008001602
 080-40969981

TAG001
DEVELOPMENT OF SOLAR SEGAWAY

ABSTRACTIn this project work, two wheeled and one small supporting wheel self-balancing as well as manually balancing Mechanical Segway vehicle is prepared which is also known as a personal transporter Segway. The system is able to operate in transporter mode and robotic mode. The first goal is to maintain stabilization in pitch dynamic. This project focuses on to manufactured Segway without using any type programming & Sensors a state feedback to stabilize system on transporter mode. The system consist of forward and backward movement when the driver operating DPDT switch in transporter mode in order to stabilize body. Small wheel is used so that there is no need of gyroscope for balancing purpose. The aim of this project work is to build up at a very low cost, highly efficient rate and easy to handle and operating also. The tests are performed on mechanical Segway to confirm that Mechanical Segway operating very well and high efficient rate. Contact:
 +91-9008001602
 080-40969981

TAG002
DEVELOPMENT OF WIND POWERED CAR

ABSTRACT--The main aim of our project is to develop a “Automatic tyre inflation and deflation system” .This can be placed in all automobiles while long drives and that can be utilized while climbing uphill or down hills. It is very necessary for the every automobile to be cautious while driving through long distances. So we have fabricated this machine to fill the air automatically by using control units. In this project main function is suddenly the air is decreased to the automobile vehicles the sensor signal alerted to the person when the use of air tank to fill the air in the tyre. Then the air pressure is increased to the tyre in the vehicle i t is same as the process of indicating the sensor signal through the person when the use of solenoid valve to reduce the excess air in the tyre Contact:
 +91-9008001602
 080-40969981

TAG007
COMPRESSED AIR VEHICLE

ABSTRACT--As the world is hard pressed with the energy and fuel crises, compounded by pollution of all kinds, any technologies that bring out the solutions to this problem is considered as a bounty. In one of such new technologies, is the development of a new engine called as compressed air engine which does not require any of the known fuels like diesel, petrol, CNG, LPG, hydrogen etc. this works using only compressed air. Contact:
 +91-9008001602
 080-40969981

TAG008
DEVELOPMENT OF REGENERATIVE POWER RESTORING USING FLYWHEEL

ABSTRACT--Regenerative brake is an energy recovery mechanism which slows a vehicle by converting its kinetic energy into another form, which can be either used immediately or stored until needed. Thus, the generated electricity during the braking is fed back into the supply system. Contact:
 +91-9008001602
 080-40969981

TAG008
FABRICATION OF 3 AXIS BULLOCK CART

ABSTRACT--Improved bullock carts will be durable (more than 25 years), which will provide better economy to the farmers or poor people for whom the bullock carts are meant for livelihood. Mechanism used in the project is as follows 1)Tilting The base of the bullock cart is rotated with the help of bevel gears and axle drive mechanism operated by the handle and lever. 2) Lifting The base of the bullock cart is lifted with the help of universal joint which is connected to lead screw which is operated by rotating the handling. Contact:
 +91-9008001602
 080-40969981

TAG001
FABRICATION OF REMOTE CONTROLLED WHEEL CHAIR CUM BED

ABSTRACT--The number of patients in India is increasing day by day. So in hospitals patients need to be shifted from wheelchair to stretcher, stretcher to beds, bed to wheelchair, or vice versa; which creates unsafe conditions for patients. Also transferring the patients from wheelchair to stretcher, stretcher to beds, bed to wheelchair is always an issue for the attendant or nurse. We will be using mild steel frames, dc motors, shafts and wheels . Contact:
 +91-9008001602
 080-40969981

TAG002
FABRICATION OF AUTOMATIC MATERIAL HANDLING ROBOT

ABSTRACT--An automated guided vehicle or automatic guided vehicle (AGV) is a mobile robot that follows markers or wires in the floor, or uses vision, magnets, or lasers for navigation. They are most often used in industrial applications to move materials around a manufacturing facility or warehouse. Contact:
 +91-9008001602
 080-40969981

TAG007
DEVELOPMENT OF AUTOMATIC PNEUMATIC BUMPER AND BRAKE ACTUATION BEFORE COLLISION

ABSTRACT--The aim is to design and develop a control system based intelligent electronically controlled automotive bumper activation and automatic braking system is called AUTOMATIC PNEUMATIC BUMPER AND BREAK ACTUATION BEFORE COLLISION. This project consists of IR transmitter and Receiver circuit, Control Unit, Pneumatic bumper system and pneumatic braking system. Contact:
 +91-9008001602
 080-40969981

TAG008
AUTOMATIC TIRE INFLATION SYSTEM

ABSTRACT--The main aim of our project is to develop a “automatic tyre inflation and deflation system” .this can be placed in all automobiles while long drives and that can be utilized while climbing uphill or down hills. it is very necessary for the every automobile to be cautious while driving through long distances. so we have fabricated this machine to fill the air automatically by using control units. in this project main function is suddenly the air is decreased to the automobile vehicles the sensor signal alerted to the person when the use of air tank to fill the air in the tyre. then the air pressure is increased to the tyre in the vehicle it is same as the process of indicating the sensor signal through the person when the use of solenoid valve to reduce the excess air in the tyre.Contact:
 +91-9008001602
 080-40969981

 

Automobile Engineering is a branch study of engineering which imparts manufacturing, designing, mechanical mechanisms as well operations of automobiles. It is an introduction to vehicle engineering which deals with motorcycles, cars, buses trucks etc. It includes branch learning of mechanical, electronic, software and safety elements. Some of the engineering attributes and disciplines that are of importance to the automotive engineer and many of the other aspects are included in it.

An automobile project doesn’t mean that you should build an entire motor vehicle. Nobody really expects you to do that. What they expect from you is something new that can be added to automobiles to increase their efficiency, comfort or reduce costs. Find a good project idea and execute it.

Back to Top